CUET PG PYQs for Strength of Materials with Solutions: Practice CUET PG Previous Year Questions

Content Writer | Journalism Graduate | Updated 3+ months ago

Strength of Materials is an important topic in the Civil Structural and Transport Engineering section in CUET PG exam. Practising this topic will increase your score overall and make your conceptual grip on CUET PG exam stronger.

This article gives you a full set of CUET PG PYQs for Strength of Materials with explanations for effective preparation. Practice of CUET PG Civil Structural and Transport Engineering PYQs including Strength of Materials questions regularly will improve accuracy, speed, and confidence in the CUET PG 2026 exam.

CUET PG PYQs for Strength of Materials with Solutions

1.
Match List - I with List - II.

Choose the correct answer from the options given below :
- A-I, B-IV, C-III, D-II
- A-IV, B-II, C-III, D-I
- A-II, B-III, C-IV, D-I
- A-III, B-IV, C-II, D-I
View Solution
2.
Arrange the following steps in correct sequence to construct Mohr’s circle for a given plane stress $(\sigma_x, \sigma_y, \tau_{xy})$: A. Plot center at $\left(\frac{\sigma_x+\sigma_y}{2}, 0\right)$
B. Identify principal stresses as horizontal intercepts
C. Plot points $X(\sigma_x,-\tau_{xy})$ and $Y(\sigma_y,\tau_{xy})$
D. Connect points X and Y and draw a circle
- C, A, D, B
- A, D, B, C
- C, A, B, D
- A, C, D, B
View Solution
3.
Match List - I with List - II.

Choose the correct answer from the options given below :
- A-IV, B-III, C-II, D-I
- A-II, B-I, C-IV, D-III
- A-I, B-II, C-III, D-IV
- A-III, B-IV, C-I, D-II
View Solution
4.
The correct order of effective length $(L_e)$ of the column for the following support condition is: A. Pinned - Pinned
B. Fixed - Free
C. Fixed - Fixed
D. Pinned - Fixed
- A > B > C > D
- B > A > D > C
- C > B > A > D
- D > C > A > B
View Solution
5.
According to maximum shear stress theory, the yield strength in shear $(\tau_s)$ and yield strength in tension $(\sigma_t)$ is related as:
- $\tau_s = \sigma_t$
- $\tau_s = \frac{\sigma_t}{2}$
- $\sigma_t = \frac{\tau_s}{2}$
- $\sigma_t = \frac{\tau_s}{\sqrt{2}}$
View Solution
6.
Match List - I with List - II.

Choose the correct answer from the options given below :
- A-III, B-IV, C-II, D-I
- A-IV, B-III, C-I, D-II
- A-II, B-I, C-IV, D-III
- A-II, B-IV, C-I, D-III
View Solution
7.
A shaft was initially subjected to bending moment and then subjected to torsion. If the magnitude of bending moment is same as that of torque, the ratio of maximum bending stress to shear stress would be:
- 0.50
- 0.25
- 2.0
- 4.0
View Solution
8.
A rectangular section has width $b$ and depth $d$ and a symmetrical triangular section has base $b$ and depth $d$. The ratio of moment of inertia of rectangular section to that of triangular section with respect to their respective centroidal axis will be:
- 1.5
- 2.0
- 3.0
- 4.0
View Solution
9.
Match List - I with List - II.

Choose the correct answer from the options given below :
- A-I, B-IV, C-II, D-III
- A-II, B-I, C-III, D-IV
- A-III, B-II, C-IV, D-I
- A-IV, B-II, C-III, D-I
View Solution
10.
What is the ordinate of influence line at Q for reaction at S as shown in figure given below ? (Beam P-Q-R-S with internal hinge at Q, supports at P, R, and S. Distances: PQ=3m, QR=3m, RS=6m)
(Aromatic compound with an isobutyl side chain) $\xrightarrow[KOH, Heat]{KMnO_4}$ ?
- 0.0
- 2.0
- 0.5
- 0.2
View Solution
11.
A steel wire of $20$ mm diameter is bent into a circular shape of $10$ m radius. If modulus of elasticity of wire is $2\times10^{5}\ \text{N/mm}^2$, then the maximum bending stress induced in wire is:
- $100\ \text{N/mm}^2$
- $200\ \text{N/mm}^2$
- $300\ \text{N/mm}^2$
- $400\ \text{N/mm}^2$
View Solution
12.
Match List-I with List-II.
List-I List-II
A. Toughness
B. Endurance Strength
C. Resistance to Abrasion
D. Deflection in beam I. Moment area method
II. Hardness
III. Energy absorbed before fracture
IV. Fatigue loading
- A-IV, B-III, C-II, D-I
- A-III, B-IV, C-I, D-II
- A-III, B-IV, C-II, D-I
- A-II, B-III, C-I, D-IV
View Solution
13.
When a component is subjected to varying (sinusoidal) load, which statements are correct: A. Mean stress is zero for fluctuating stress
B. Minimum stress is zero for repeated stress
C. Mean stress is zero for reversed stress
D. Amplitude stress is the average of minimum and maximum stress
- A and B only
- B and C only
- C and D only
- B, C and D only
View Solution
14.
Match List - I with List - II.

Choose the correct answer from the options given below :
- A-I, B-III, C-IV, D-II
- A-II, B-I, C-II, D-IV
- A-IV, B-II, C-III, D-I
- A-II, B-IV, C-I, D-III
View Solution
15.
Two identical circular rods of same diameter and length are subjected to same axial tensile force. One is mild steel and other aluminium. Which is correct?
- Both rods elongate by same amount
- Mild steel elongates more
- Aluminium elongates more
- All stresses, strains equal
View Solution

List-I	List-II
A. Toughness B. Endurance Strength C. Resistance to Abrasion D. Deflection in beam	I. Moment area method II. Hardness III. Energy absorbed before fracture IV. Fatigue loading

View more CUET PG Questions

SHARE ON FACEBOOK SHARE ON TWITTER

Comments

No Comments To Show

SUBSCRIBE TO OUR NEWS LETTER

COLLEGE NOTIFICATIONS

EXAM NOTIFICATIONS

NEWS UPDATES

Download the Collegedunia app on

CUET PG PYQs for Strength of Materials with Solutions: Practice CUET PG Previous Year Questions

CUET PG PYQs for Strength of Materials with Solutions

1.
Match List - I with List - II.

Choose the correct answer from the options given below :

3.
Match List - I with List - II.

Choose the correct answer from the options given below :

4.
The correct order of effective length \((L_e)\) of the column for the following support condition is: A. Pinned - Pinned
B. Fixed - Free
C. Fixed - Fixed
D. Pinned - Fixed

5.
According to maximum shear stress theory, the yield strength in shear \((\tau_s)\) and yield strength in tension \((\sigma_t)\) is related as:

6.
Match List - I with List - II.

Choose the correct answer from the options given below :

7.
A shaft was initially subjected to bending moment and then subjected to torsion. If the magnitude of bending moment is same as that of torque, the ratio of maximum bending stress to shear stress would be:

8.
A rectangular section has width $b$ and depth $d$ and a symmetrical triangular section has base $b$ and depth $d$. The ratio of moment of inertia of rectangular section to that of triangular section with respect to their respective centroidal axis will be:

9.
Match List - I with List - II.

Choose the correct answer from the options given below :

10.
What is the ordinate of influence line at Q for reaction at S as shown in figure given below ? (Beam P-Q-R-S with internal hinge at Q, supports at P, R, and S. Distances: PQ=3m, QR=3m, RS=6m)
(Aromatic compound with an isobutyl side chain) $\xrightarrow[KOH, Heat]{KMnO_4}$ ?

11.
A steel wire of $20$ mm diameter is bent into a circular shape of $10$ m radius. If modulus of elasticity of wire is $2\times10^{5}\ \text{N/mm}^2$, then the maximum bending stress induced in wire is:

12.
Match List-I with List-II.
List-I List-II
A. Toughness
B. Endurance Strength
C. Resistance to Abrasion
D. Deflection in beam I. Moment area method
II. Hardness
III. Energy absorbed before fracture
IV. Fatigue loading

13.
When a component is subjected to varying (sinusoidal) load, which statements are correct: A. Mean stress is zero for fluctuating stress
B. Minimum stress is zero for repeated stress
C. Mean stress is zero for reversed stress
D. Amplitude stress is the average of minimum and maximum stress

14.
Match List - I with List - II.

Choose the correct answer from the options given below :

15.
Two identical circular rods of same diameter and length are subjected to same axial tensile force. One is mild steel and other aluminium. Which is correct?

Comments

SUBSCRIBE TO OUR NEWS LETTER

CUET PG PYQs for Strength of Materials with Solutions

1.Match List - I with List - II. Choose the correct answer from the options given below :

3.Match List - I with List - II. Choose the correct answer from the options given below :

4.The correct order of effective length \((L_e)\) of the column for the following support condition is: A. Pinned - Pinned B. Fixed - Free C. Fixed - Fixed D. Pinned - Fixed

5.According to maximum shear stress theory, the yield strength in shear \((\tau_s)\) and yield strength in tension \((\sigma_t)\) is related as:

6.Match List - I with List - II. Choose the correct answer from the options given below :

7.A shaft was initially subjected to bending moment and then subjected to torsion. If the magnitude of bending moment is same as that of torque, the ratio of maximum bending stress to shear stress would be:

8.A rectangular section has width $b$ and depth $d$ and a symmetrical triangular section has base $b$ and depth $d$. The ratio of moment of inertia of rectangular section to that of triangular section with respect to their respective centroidal axis will be:

9.Match List - I with List - II. Choose the correct answer from the options given below :

10.What is the ordinate of influence line at Q for reaction at S as shown in figure given below ? (Beam P-Q-R-S with internal hinge at Q, supports at P, R, and S. Distances: PQ=3m, QR=3m, RS=6m) (Aromatic compound with an isobutyl side chain) $\xrightarrow[KOH, Heat]{KMnO_4}$ ?

11.A steel wire of $20$ mm diameter is bent into a circular shape of $10$ m radius. If modulus of elasticity of wire is $2\times10^{5}\ \text{N/mm}^2$, then the maximum bending stress induced in wire is:

12.Match List-I with List-II.List-IList-IIA. ToughnessB. Endurance StrengthC. Resistance to AbrasionD. Deflection in beamI. Moment area methodII. HardnessIII. Energy absorbed before fractureIV. Fatigue loading

13.When a component is subjected to varying (sinusoidal) load, which statements are correct: A. Mean stress is zero for fluctuating stress B. Minimum stress is zero for repeated stress C. Mean stress is zero for reversed stress D. Amplitude stress is the average of minimum and maximum stress

14.Match List - I with List - II. Choose the correct answer from the options given below :

15.Two identical circular rods of same diameter and length are subjected to same axial tensile force. One is mild steel and other aluminium. Which is correct?

Comments

SUBSCRIBE TO OUR NEWS LETTER

1.
Match List - I with List - II.

Choose the correct answer from the options given below :

3.
Match List - I with List - II.

Choose the correct answer from the options given below :

4.
The correct order of effective length \((L_e)\) of the column for the following support condition is: A. Pinned - Pinned
B. Fixed - Free
C. Fixed - Fixed
D. Pinned - Fixed

5.
According to maximum shear stress theory, the yield strength in shear \((\tau_s)\) and yield strength in tension \((\sigma_t)\) is related as:

6.
Match List - I with List - II.

Choose the correct answer from the options given below :

7.
A shaft was initially subjected to bending moment and then subjected to torsion. If the magnitude of bending moment is same as that of torque, the ratio of maximum bending stress to shear stress would be:

8.
A rectangular section has width $b$ and depth $d$ and a symmetrical triangular section has base $b$ and depth $d$. The ratio of moment of inertia of rectangular section to that of triangular section with respect to their respective centroidal axis will be:

9.
Match List - I with List - II.

Choose the correct answer from the options given below :

10.
What is the ordinate of influence line at Q for reaction at S as shown in figure given below ? (Beam P-Q-R-S with internal hinge at Q, supports at P, R, and S. Distances: PQ=3m, QR=3m, RS=6m)
(Aromatic compound with an isobutyl side chain) $\xrightarrow[KOH, Heat]{KMnO_4}$ ?

11.
A steel wire of $20$ mm diameter is bent into a circular shape of $10$ m radius. If modulus of elasticity of wire is $2\times10^{5}\ \text{N/mm}^2$, then the maximum bending stress induced in wire is:

12.
Match List-I with List-II.
List-I List-II
A. Toughness
B. Endurance Strength
C. Resistance to Abrasion
D. Deflection in beam I. Moment area method
II. Hardness
III. Energy absorbed before fracture
IV. Fatigue loading

13.
When a component is subjected to varying (sinusoidal) load, which statements are correct: A. Mean stress is zero for fluctuating stress
B. Minimum stress is zero for repeated stress
C. Mean stress is zero for reversed stress
D. Amplitude stress is the average of minimum and maximum stress

14.
Match List - I with List - II.

Choose the correct answer from the options given below :

15.
Two identical circular rods of same diameter and length are subjected to same axial tensile force. One is mild steel and other aluminium. Which is correct?