Resistors in Series and Parallel MCQ

Content Curator

Resistors in series and parallel are the two ways of connection in a circuit. A resistor is an electrical component that provides electrical resistance which can be used to leverage the amount of current flowing through the circuit. This topic has more weightage in Class 12 Chapter 3 Current Electricity. In a series connection, the resistors are connected end to end whereas, in a parallel connection, the resistors are connected in parallel to one another.

The total resistance of resistors in series is given by,

R_total = R₁ + R₂ + ….. + R_n

The total resistance of resistors in parallel is given by,

\(\frac{1}{R_{Total}}= \frac{1}{R_1}+ \frac{1}{R_2} + \frac{1}{R_3} +...\frac{1}{R_n}\)

Check Out:

Topic Related Articles
Kirchhoff’s Laws MCQ	Kirchhoff’s Laws Important Questions	Cells in series and parallel MCQ
Wheatstone Bridge MCQ	Wheatstone Bridge Important Questions	Cells in series and parallel Important questions

Resistors in Series and Parallel MCQ

Ques 1. In series connection of resistors, what happens to the current across each resistor?

a) Increases

b) Decreases

c) Remain the same

d) Initially increases and then decreases

Click here for the answer

Answer: c

Explanation: When the resistors are connected in series, and current is passed through them, the current passing through each of the resistors is the same. This is because the resistors are connected end to the end and, therefore, there is only one path for the current to flow through.

Ques 2. Identify the combination which is not a series connection.

a) Resistance box

b) Decorative bulbs

c) Fuses

d) Domestic appliances

Click here for the answer

Answer: d

Explanation: Domestic appliances in a house are connected in parallel combinations, and not in series combinations. This arrangement is done so that each of the appliances can switch on and off independently and does not alter the connection with the other appliances.

Ques 3. The equivalent overall resistance in a parallel connection is smaller than the series connection.

a) True

b) False

Click here for the answer

Answer. a

Explanation: As we all know the total resistance of resistors in a series circuit is Rtotal = R1 + R2 + ….. + Rn, whereas for a parallel circuit, it is, \(\frac{1}{R_{Total}}= \frac{1}{R_1}+ \frac{1}{R_2} + \frac{1}{R_3} +...\frac{1}{R_n}\). Since in parallel circuit, it is the reciprocal of the resistances, it tends to be smaller than series connection.

Ques 4. Calculate resultant resistance between the points A and B in the circuit shown in the figure below.

Calculate resultant resistance between the points A and B in the circuit

a) 4 ohms

b) 2 ohms

c) 8 ohms

d) 6 ohms

Click here for the answer

Answer: b

Explanation: We can simplify the given diagram as follows:

From the diagram above, we can take the middle resistors connected in series and then calculate all the other resistors connected in parallel.

\(\frac{1}{R_1} = \frac{1}{4} + \frac{1}{8} = \frac{4+6}{4 * 6} = \frac {10}{24}\) → R₁ = \(\frac{24}{10}\) = 2.4

\(\frac{1}{R_2} = \frac{1}{2} + \frac{1}{8} = \frac{2+8}{2 * 8} = \frac {10}{16}\)→ R₂ = \(\frac{16}{10}\) = 1.6

Now, R1 and R2 are in series, so, Rs = 2.4 + 1.6 = 4.0.

8 ohms, Rs, and the bottom 8 ohms are in parallel, so, 1/Rp = ⅛ + ¼ + ⅛ = ½

On taking the inverse of Rp, we get, Rp = 2 ohms.

Ques 5. Two wires of the same material have the same length but their radii are in the ratio of 5:3. They are combined in series, where the resistance of the thicker wire is 12 ohms. Calculate the total resistance of the combination.

a) 40

b) 12

c) 32

d) 20

Click here for the answer

Answer: c

Explanation: The given ratio of radii = 5:3;

R2/R1 = 5/3

R2 = 5/3 x R1

R1 = 12 ohms (given)

R2 = 5/3 x 12

R2 = 20

Total resistance of resistors connected in series Rs = R1 + R2

Rs = 20 + 12

Rs = 32 ohms

Check Out:

Related Articles
Cells in series and parallel	Cells, emf, Internal Resistance	Electrical Current
Resistor Colour Codes	Circuit Diagram	Electromotive Force
Uses of Resistor	Resistance Formula	Internal resistance formula

Ques 6. Two resistors are connected in parallel, whose resistance values are in the ratio 3:1. Find the ratio of power dissipated.

a) 1:3

b) 3:1

c) 1:2

d) 2:1

Click here for the answer

Answer: a

Explanation: We know that,

Power = voltage²/ resistance

Since the resistors are connected in parallel, the voltage across them will be the same.

From this relation, power and resistance are inversely proportional to each other.

Thus, P1/P2 = R2/R1 =1/3

So, the power dissipated is in the ratio of 1:3.

Ques 7. A circuit has three similar resistors, each of 20 ohms resistance. Two of them are connected in parallel, and this combination is connected in series with the third one. The maximum power that can be consumed by each resistor is 30 W. Then, what is the maximum power that can be consumed by the combination of all three resistors?

a) 30

b) 20

c) 35

d) 45

Click here for the answer

Answer: d

Explanation: The equivalent overall resistance of the parallel combination is:

1/R1 = 1/20 + 1/20 = 2/20 = 1/10

On taking reciprocal,

R1 = 10 ohms.

R1 is in series with R2; So, R3 = R1 + R2 = 10 + 20 = 30 ohms.

Now, we can employ the method of cross-multiplication:

For 20 ohms resistor → 30 W power consumed

For 30 ohms resistor combination → x

20x = 30 × 30

x = 30×30/ 20

x = 45

Therefore, the power consumed by the parallel combination is 45 ohms.

Ques 8. Which connection is preferable to connect bulbs?

a) Series

b) Parallel

c) Both series and parallel

d) Neither series nor parallel

Click here for the answer

Answer: b

Explanation: Bulbs are connected in parallel so that even if one of the bulbs blows out, the others continue to get a current supply. This is why parallel connection is used in domestic electrical circuits.

Ques 9. Batteries are generally connected?

a) Series

b) Parallel

c) Either series or parallel

d) Neither series nor parallel

Click here for the answer

Answer: a

Explanation: Batteries are generally connected in series so that we can obtain the desired voltage since voltages add up once they are connected in series.

Ques 10. In a _________ circuit, the total resistance is greater than the largest resistance in the circuit.

a) Series

b) Parallel

c) Either series or parallel

d) Neither series nor parallel

Click here for the answer

Answer: a

Explanation: In series circuits, the total resistance is the sum of all the resistance in the circuit, hence the total is greater than the largest resistance.

Ques 11. In a ____________ circuit, the total resistance is smaller than the smallest resistance in the circuit.

a) Series

b) Parallel

c) Either series or parallel

d) Neither series nor parallel

Click here for the answer

Answer: b

Explanation: Since the equivalent resistance is 1/sum of the reciprocals of all the resistances in the circuit, it is smaller than the smallest resistance in the circuit.

Ques 12. Which connection is the most cost-efficient connection?

a) Series

b) Parallel

c) Either series or parallel

d) Neither series nor parallel

Click here for the answer

Answer: a

Explanation: The advantage of series connection is that they share the supply voltage, hence cheap low voltage appliances may be used.

Ques 13. Calculate the equivalent resistance between A and B.

Calculate the equivalent resistance between A and B.

a) 2 ohm

b) 4 ohm

c) 6 ohm

d) 8 ohm

Click here for the answer

Answer: a

Explanation: The 2 and the 3 ohm resistors are in series.

R1 = 3 + 2 = 5

The equivalent of these two resistors is in parallel with the 5 ohm resistor.

1/R2 = 1/R1 + ⅕

= ⅕ + ⅕

= ⅖

R2 = 5/2

The equivalent of these three resistances is in series with the 1.5 ohm resistor.

R3 = R2 + 1.5

R3 = 5/2 + 1.5

R3 = 2.5 + 1.5

R3 = 4 ohm

Finally, the equivalent of these resistances is in parallel with the 4 ohm resistor.

1/R4 = ¼ + ¼

1/R4 = 2/4 = ½

R4 = 2 ohm

Ques 14. Calculate the equivalent resistance between A and B.

Calculate the equivalent resistance between A and B

a) 6.67 ohm

b) 46.67 ohm

c) 26.67 ohm

d) 10.67 ohm

Click here for the answer

Answer: b

Explanation: The three 20 ohm resistors in the middle are in parallel to each other.

1/R1 = 1/20 + 1/20 + 1/20 = 3/20

R1 = 20/3

The rest of the resistors are in series.

R2 = 20 + 20 + 20/3

R2 = 46.67 ohm

Read More:

PCMB Guide Articles
Important Physics Formulae	Current Electricity Important Questions	NCERT Solutions for Class 12 Chemistry
Comparison Articles in Physics	Class 12 Physics Book Pdf	CBSE Class 12 Physics Practicals
NCERT Solutions for Class 12 Maths	Class 12 Maths Book	Important Physics Constants
SI Units in Physics	Important Physics MCQs	NCERT Solutions for Class 12 Physics
NCERT Class 12 PCMB Textbook	Class 12 PCMB Notes	Class 12 Biology Book Pdf
NCERT Solutions for Class 12 Biology	Class 12 PCMB Textbooks	Physics Study Material
Important Physics Derivations	Class 12 Physics Notes	Class 12 English Book Pdf

Resistors in Series and Parallel MCQ

Resistors in Series and Parallel MCQ

CBSE CLASS XII Related Questions

1.
What is displacement current (\( i_d \))? Considering the case of charging of a capacitor, show that \( i_d = \varepsilon_0 \frac{d\Phi_E}{dt} \). What is the value of \( i_d \) for a conductor across which a constant voltage is applied?

2.
Photoemission of electrons occurs from a metal (\( \phi_0 = 1.96 \, \text{eV} \)) when light of frequency \( 6.4 \times 10^{14} \, \text{Hz} \) is incident on it. Calculate: Energy of a photon in the incident light, The maximum kinetic energy of the emitted electrons, and The stopping potential.

3.
Two thin lenses of focal length \( f_1 \) and \( f_2 \) are placed in contact with each other coaxially. Prove that the focal length \( f \) of the combination is given by \[ f = \frac{f_1 f_2}{f_1 + f_2}. \]

4.
Suppose a pure Si crystal has \( 5 \times 10^{28} \) atoms per \( \text{m}^3 \). It is doped with \( 5 \times 10^{22} \) atoms per \( \text{m}^3 \) of Arsenic. Calculate majority and minority carrier concentration in the doped silicon. (Given: \( n_i = 1.5 \times 10^{16} \, \text{m}^{-3} \))

5.
If both the number of protons and the neutrons are conserved in each nuclear reaction, in what way is mass converted into energy (or vice versa) in a nuclear reaction? Explain.

Similar Physics Concepts

Comments

SUBSCRIBE TO OUR NEWS LETTER

Resistors in Series and Parallel MCQ

Resistors in Series and Parallel MCQ

CBSE CLASS XII Related Questions

1.What is displacement current (\( i_d \))? Considering the case of charging of a capacitor, show that \( i_d = \varepsilon_0 \frac{d\Phi_E}{dt} \). What is the value of \( i_d \) for a conductor across which a constant voltage is applied?

2.Photoemission of electrons occurs from a metal (\( \phi_0 = 1.96 \, \text{eV} \)) when light of frequency \( 6.4 \times 10^{14} \, \text{Hz} \) is incident on it. Calculate: Energy of a photon in the incident light, The maximum kinetic energy of the emitted electrons, and The stopping potential.

3.Two thin lenses of focal length \( f_1 \) and \( f_2 \) are placed in contact with each other coaxially. Prove that the focal length \( f \) of the combination is given by \[ f = \frac{f_1 f_2}{f_1 + f_2}. \]

4.Suppose a pure Si crystal has \( 5 \times 10^{28} \) atoms per \( \text{m}^3 \). It is doped with \( 5 \times 10^{22} \) atoms per \( \text{m}^3 \) of Arsenic. Calculate majority and minority carrier concentration in the doped silicon. (Given: \( n_i = 1.5 \times 10^{16} \, \text{m}^{-3} \))

5. If both the number of protons and the neutrons are conserved in each nuclear reaction, in what way is mass converted into energy (or vice versa) in a nuclear reaction? Explain.

Similar Physics Concepts

Comments

SUBSCRIBE TO OUR NEWS LETTER

1.
What is displacement current (\( i_d \))? Considering the case of charging of a capacitor, show that \( i_d = \varepsilon_0 \frac{d\Phi_E}{dt} \). What is the value of \( i_d \) for a conductor across which a constant voltage is applied?

2.
Photoemission of electrons occurs from a metal (\( \phi_0 = 1.96 \, \text{eV} \)) when light of frequency \( 6.4 \times 10^{14} \, \text{Hz} \) is incident on it. Calculate: Energy of a photon in the incident light, The maximum kinetic energy of the emitted electrons, and The stopping potential.

3.
Two thin lenses of focal length \( f_1 \) and \( f_2 \) are placed in contact with each other coaxially. Prove that the focal length \( f \) of the combination is given by \[ f = \frac{f_1 f_2}{f_1 + f_2}. \]

4.
Suppose a pure Si crystal has \( 5 \times 10^{28} \) atoms per \( \text{m}^3 \). It is doped with \( 5 \times 10^{22} \) atoms per \( \text{m}^3 \) of Arsenic. Calculate majority and minority carrier concentration in the doped silicon. (Given: \( n_i = 1.5 \times 10^{16} \, \text{m}^{-3} \))

5.
If both the number of protons and the neutrons are conserved in each nuclear reaction, in what way is mass converted into energy (or vice versa) in a nuclear reaction? Explain.