GATE 2003 Electrical Engineering (EE) Question Paper with Answer Key pdf is available for download. The exam was conducted by IIT Madras on February 9, 2003. The question paper comprised a total of 90 questions from General Aptitude and Electrical Engineering (EE) topics.
GATE 2003 Electrical Engineering (EE) Question Paper with Answer Key PDF
GATE 2003 Electrical Engineering (EE) Question Paper PDF
GATE 2003 Electrical Engineering (EE) Answer Key PDF
Convective heat transfer coefficients for Fluid 1 and Fluid 2 in a heat exchanger, as shown in the figure below, are 50 W/(m2K) and 80 W/(m2K), respectively. The inner tube is made of a material which has a thermal conductivity 386 W/(m K) for the given range of temperatures in the heat exchanger. The length of the heat exchanging surface, the inside radius of the inner tube, and thickness of the inner tube are 1 m, 10 mm, and 1 mm, respectively. Considering no heat exchange between the outer tube and the surrounding, the heat transfer rate for the heat exchanger is ________ W (rounded off to 1 decimal place).
A liquid comes out of the reactor of a chemical plant at 250 °C temperature with a flow rate of 100 LPM. The ambient temperature is 25 °C. Density and specific heat of the liquid remain constant at 1000 kg/m3 and 4.18 kJ/kg K, respectively, for the given range of temperature. The rate of exergy associated with the hot liquid stream at the exit of the plant is ________ kW (rounded off to 2 decimal places).
A rigid closed vertical cylindrical vessel of 15 cm diameter contains 5 kg water at 80 °C with 10% quality. The water is heated till its temperature reaches 130 °C. Considering only a horizontal separated interface between liquid and vapor, the dip in the liquid level after the heating process is ________ cm (rounded off to 2 decimal places). Properties of water at various saturation temperatures are given in the table below.
T (°C)
vf (m3/kg)
vg (m3/kg)
uf (kJ/kg)
ug (kJ/kg)
80
0.001029
3.4053
334.97
2481.60
130
0.001070
0.66808
546.10
2539.50
T, v, and u are temperature, specific volume, and specific internal energy, respectively. Subscripts f and g represent saturated liquid and saturated vapor, respectively.
A drill bit during its lifetime can produce \(150\) through holes in a plate at a drill speed of \(200\) RPM. If the drill speed increases to \(300\) RPM, it can produce \(60\) through holes in the same plate before the drill bit fails. Assuming all other parameters remain constant, the value of the exponent in Taylor's tool life equation is ________ (rounded off to 2 decimal places).
The activities of a PERT network and their corresponding activity time estimates (in weeks), namely optimistic (\(t_o\)), most likely (\(t_m\)), and pessimistic (\(t_p\)), are given in the table below.
Activity
\(t_o\)
\(t_m\)
\(t_p\)
1-2
2
4
12
1-3
2
4
6
1-4
3
4
11
2-5
3
6
9
3-4
2
5
14
3-5
3
3
3
4-5
3
6
15
5-6
2
5
8
The expected project length is ________ weeks (in integer).
Two rectangular surfaces both having 1 m2 area are placed perpendicular to each other with a common edge. One surface is hot, having a temperature of 1000 K and emissivity of 0.4, while the other is insulated and in radiant balance with a large surrounding room at 300 K. If the fraction of radiation leaving the hot surface which reaches the cold surface is 0.2, then the equivalent overall resistance for the radiation heat loss from the hot surface is _______ m-2 (rounded off to 2 decimal places).
Comments